i855 and i810 clone view probl

[Alex Deucher]

On Thu, 2 Dec 2004 19:39 +0100, hephaistos6 at sms.at <hephaistos6 at sms.at> wrote:
> hello,
> 
> I gave up to have xinerama support on my toshiba satellite pro a10 with onBoard i855 graphics.
> But at least clone view (vga out for beamers, externals monitors etc) I will try to get working correct.
> 
> lspci concerning my i855 returns:
> 0000:00:02.0 VGA compatible controller: Intel Corp. 82852/855GM Integrated Graphics Device (rev 01)
> 0000:00:02.1 Display controller: Intel Corp. 82852/855GM Integrated Graphics Device (rev 01)
> 
> I have no "generic" monitor in my xorg.conf. I use the latest release of xorg on gentoo linux.
> when I start xorg I get some strange warnings concerning pipes:

you may need the "monitorlayout" and/or the "clone" options in your
device config.

Alex

> --------------------------
> (II) I810(0): Integrated Graphics Chipset: Intel(R) 852GM
> (--) I810(0): Chipset: "852GM/855GM"
> (--) I810(0): Linear framebuffer at 0xD8000000
> (--) I810(0): IO registers at addr 0xD0000000
> (II) I810(0): 2 display pipes available.
> (II) I810(0): detected 16252 kB stolen memory.
> (II) I810(0): I830CheckAvailableMemory: 434172 kB available
> (II) I810(0): Checking Lid status enabled
> (--) I810(0): Pre-allocated VideoRAM: 16252 kByte
> (==) I810(0): VideoRAM: 32768 kByte
> (==) I810(0): video overlay key set to 0x101fe
> (**) I810(0): page flipping disabled
> (==) I810(0): Using gamma correction (1.0, 1.0, 1.0)
> (II) I810(0): BIOS Build: 2894
> (==) I810(0): Device Presence: disabled.
> (WW) I810(0): Primary Pipe is B, switching off second monitor (0x800)
> (==) I810(0): Display Info: enabled.
> (II) I810(0): Broken BIOSes cause the system to hang here.
>               If you encounter this problem please add
>                  Option "DisplayInfo" "FALSE"
>               to the Device section of your XF86Config file.
> (II) I810(0): Display Info: CRT: attached: FALSE, present: TRUE, size: (0,0)
> (II) I810(0): Display Info: TV: attached: FALSE, present: FALSE, size: (0,0)
> (II) I810(0): Display Info: DFP (digital flat panel): attached: FALSE, present: FALSE, size: (0,0)
> (II) I810(0): Display Info: LFP (local flat panel): attached: TRUE, present: TRUE, size: (1024,768)
> (II) I810(0): Display Info: CRT2 (second CRT): attached: FALSE, present: FALSE, size: (0,0)
> (II) I810(0): Display Info: TV2 (second TV): attached: FALSE, present: FALSE, size: (0,0)
> (II) I810(0): Size of device LFP (local flat panel) is 1024 x 768
> (II) I810(0): No active displays on Pipe A.
> (II) I810(0): Currently active displays on Pipe B:
> (II) I810(0):   LFP (local flat panel)
> (II) I810(0): Lowest common panel size for pipe B is 1024 x 768
> (==) I810(0): Display is using Pipe B
> (--) I810(0): Maximum frambuffer space: 32600 kByte
> (II) Loading sub module "ddc"
> (II) LoadModule: "ddc"
> (II) Loading /usr/lib/modules/libddc.a
> (II) Module ddc: vendor="X.Org Foundation"
>         compiled for 6.8.0, module version = 1.0.0
>         ABI class: X.Org Video Driver, version 0.7
> (II) I810(0): VESA VBE DDC supported
> (II) I810(0): VESA VBE DDC Level 2
> (II) I810(0): VESA VBE DDC transfer in appr. 1 sec.
> (II) I810(0): VESA VBE DDC read failed
> (--) I810(0): A non-CRT device is attached to pipe B.
>         No refresh rate overrides will be attempted.
> (II) I810(0): Will use BIOS call 0x5f05 to set refresh rates for CRTs.
> --------------------------
> I tried i810switch and i855crt but none are working...
> 
> Does anyone have any information for me? If you need further information please tell me -> I'll provide them...
> 
> thx in advance,
> stefan walkner
> 
> --
> Ein Service von http://www.sms.at
> 
> _______________________________________________
> xorg mailing list
> xorg at lists.freedesktop.org
> http://lists.freedesktop.org/mailman/listinfo/xorg
>