i855 and i810 clone view probl

[hephaistos6 at sms.at]

hello,

I gave up to have xinerama support on my toshiba satellite pro a10 with onBoard i855 graphics.
But at least clone view (vga out for beamers, externals monitors etc) I will try to get working correct.

lspci concerning my i855 returns:
0000:00:02.0 VGA compatible controller: Intel Corp. 82852/855GM Integrated Graphics Device (rev 01)
0000:00:02.1 Display controller: Intel Corp. 82852/855GM Integrated Graphics Device (rev 01)

I have no "generic" monitor in my xorg.conf. I use the latest release of xorg on gentoo linux.
when I start xorg I get some strange warnings concerning pipes:
--------------------------
(II) I810(0): Integrated Graphics Chipset: Intel(R) 852GM
(--) I810(0): Chipset: "852GM/855GM"
(--) I810(0): Linear framebuffer at 0xD8000000
(--) I810(0): IO registers at addr 0xD0000000
(II) I810(0): 2 display pipes available.
(II) I810(0): detected 16252 kB stolen memory.
(II) I810(0): I830CheckAvailableMemory: 434172 kB available
(II) I810(0): Checking Lid status enabled
(--) I810(0): Pre-allocated VideoRAM: 16252 kByte
(==) I810(0): VideoRAM: 32768 kByte
(==) I810(0): video overlay key set to 0x101fe
(**) I810(0): page flipping disabled
(==) I810(0): Using gamma correction (1.0, 1.0, 1.0)
(II) I810(0): BIOS Build: 2894
(==) I810(0): Device Presence: disabled.
(WW) I810(0): Primary Pipe is B, switching off second monitor (0x800)
(==) I810(0): Display Info: enabled.
(II) I810(0): Broken BIOSes cause the system to hang here.
              If you encounter this problem please add
                 Option "DisplayInfo" "FALSE"
              to the Device section of your XF86Config file.
(II) I810(0): Display Info: CRT: attached: FALSE, present: TRUE, size: (0,0)
(II) I810(0): Display Info: TV: attached: FALSE, present: FALSE, size: (0,0)
(II) I810(0): Display Info: DFP (digital flat panel): attached: FALSE, present: FALSE, size: (0,0)
(II) I810(0): Display Info: LFP (local flat panel): attached: TRUE, present: TRUE, size: (1024,768)
(II) I810(0): Display Info: CRT2 (second CRT): attached: FALSE, present: FALSE, size: (0,0)
(II) I810(0): Display Info: TV2 (second TV): attached: FALSE, present: FALSE, size: (0,0)
(II) I810(0): Size of device LFP (local flat panel) is 1024 x 768
(II) I810(0): No active displays on Pipe A.
(II) I810(0): Currently active displays on Pipe B:
(II) I810(0):   LFP (local flat panel)
(II) I810(0): Lowest common panel size for pipe B is 1024 x 768
(==) I810(0): Display is using Pipe B
(--) I810(0): Maximum frambuffer space: 32600 kByte
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Loading /usr/lib/modules/libddc.a
(II) Module ddc: vendor="X.Org Foundation"
        compiled for 6.8.0, module version = 1.0.0
        ABI class: X.Org Video Driver, version 0.7
(II) I810(0): VESA VBE DDC supported
(II) I810(0): VESA VBE DDC Level 2
(II) I810(0): VESA VBE DDC transfer in appr. 1 sec.
(II) I810(0): VESA VBE DDC read failed
(--) I810(0): A non-CRT device is attached to pipe B.
        No refresh rate overrides will be attempted.
(II) I810(0): Will use BIOS call 0x5f05 to set refresh rates for CRTs.
--------------------------
I tried i810switch and i855crt but none are working...

Does anyone have any information for me? If you need further information please tell me -> I'll provide them...

thx in advance,
stefan walkner

--
Ein Service von http://www.sms.at