[PATCH xserver/hw/xfree86/man/xorg.conf.man] .BI style: monitor section
vdb at picaros.org
vdb at picaros.org
Tue Aug 30 22:23:01 PDT 2011
The xorg.conf manual uses the following convention in most of its
sections:
bold = text to be copied literally to the config file,
italic = a symbolic name to be substituted by a true value.
Some configuration keywords seem to have been changed into generic
options. Prepending Option to the manual entry swapped the
bold-italic logic. This patch restores the convention in the monitor
section and consists of
-.BI "Option " "\*qPreferredMode\*q " \*qstring\*q
+.BI "Option \*qPreferredMode\*q \*q" name \*q
modifications.
Signed-off-by: Servaas Vandenberghe
diff --git a/hw/xfree86/man/xorg.conf.man b/hw/xfree86/man/xorg.conf.man
index 4bec316..7d4738a 100644
--- a/hw/xfree86/man/xorg.conf.man
+++ b/hw/xfree86/man/xorg.conf.man
@@ -1428,7 +1428,7 @@
section with an output by adding an option to the Device section in the
following format:
-.B Option \*qMonitor-outputname\*q \*qmonitorsection\*q
+.BI "Option \*qMonitor-" outputname "\*q \*q" monitorsection \*q
(for example,
.B Option \*qMonitor-VGA\*q \*qVGA monitor\*q
@@ -1444,7 +1444,7 @@ modes available.
When modes are specified explicitly in the
.B Monitor
section (with the
-.BR Modes ,
+.BR Mode ,
.BR ModeLine ,
or
.B UseModes
@@ -1593,7 +1593,7 @@ mentioned above doubles this value.
This entry is a more compact version of the
.B Mode
entry, and it also can be used to specify video modes for the monitor.
-is a single line format for specifying video modes.
+This is a single line format for specifying video modes.
In most cases this isn't necessary because the built\-in set of VESA
standard modes will be sufficient.
.PP
@@ -1648,61 +1648,61 @@ The
and
.B VScan
options mentioned above in the
-.B Modes
+.B Mode
entry description can also be used here.
.RE
.TP 7
-.BI "Option " "\*qDPMS\*q " \*qbool\*q
+.BI "Option \*qDPMS\*q \*q" bool \*q
This option controls whether the server should enable the DPMS extension
for power management for this screen. The default is to enable the
extension.
.TP 7
-.BI "Option " "\*qSyncOnGreen\*q " \*qbool\*q
+.BI "Option \*qSyncOnGreen\*q \*q" bool \*q
This option controls whether the video card should drive the sync signal
on the green color pin. Not all cards support this option, and most
monitors do not require it. The default is off.
.TP 7
-.BI "Option " "\*qPrimary\*q " \*qbool\*q
+.BI "Option \*qPrimary\*q \*q" bool \*q
This optional entry specifies that the monitor should be treated as the primary
monitor. (RandR 1.2-supporting drivers only)
.TP 7
-.BI "Option " "\*qPreferredMode\*q " \*qstring\*q
+.BI "Option \*qPreferredMode\*q \*q" name \*q
This optional entry specifies a mode to be marked as the preferred initial mode
of the monitor.
(RandR 1.2-supporting drivers only)
.TP 7
-.BI "Option " "\*qPosition\*q " "\*qx y\*q"
+.BI "Option \*qPosition\*q \*q" x " " y \*q
This optional entry specifies the position of the monitor within the X
screen.
(RandR 1.2-supporting drivers only)
.TP 7
-.BI "Option " "\*qLeftOf\*q " \*qoutput\*q
+.BI "Option \*qLeftOf\*q \*q" output \*q
This optional entry specifies that the monitor should be positioned to the
left of the output (not monitor) of the given name.
(RandR 1.2-supporting drivers only)
.TP 7
-.BI "Option " "\*qRightOf\*q " \*qoutput\*q
+.BI "Option \*qRightOf\*q \*q" output \*q
This optional entry specifies that the monitor should be positioned to the
right of the output (not monitor) of the given name.
(RandR 1.2-supporting drivers only)
.TP 7
-.BI "Option " "\*qAbove\*q " \*qoutput\*q
+.BI "Option \*qAbove\*q \*q" output \*q
This optional entry specifies that the monitor should be positioned above the
output (not monitor) of the given name.
(RandR 1.2-supporting drivers only)
.TP 7
-.BI "Option " "\*qBelow\*q " \*qoutput\*q
+.BI "Option \*qBelow\*q \*q" output \*q
This optional entry specifies that the monitor should be positioned below the
output (not monitor) of the given name.
(RandR 1.2-supporting drivers only)
.TP 7
-.BI "Option " "\*qEnable\*q " \*qbool\*q
+.BI "Option \*qEnable\*q \*q" bool \*q
This optional entry specifies whether the monitor should be turned on
at startup. By default, the server will attempt to enable all connected
monitors.
(RandR 1.2-supporting drivers only)
.TP 7
-.BI "Option " "\*qDefaultModes\*q " \*qbool\*q
+.BI "Option \*qDefaultModes\*q \*q" bool \*q
This optional entry specifies whether the server should add supported default
modes to the list of modes offered on this monitor. By default, the server
will add default modes; you should only disable this if you can guarantee
@@ -1710,21 +1710,21 @@ that EDID will be available at all times, or if you have added custom modelines
which the server can use.
(RandR 1.2-supporting drivers only)
.TP 7
-.BI "Option " "\*qMinClock\*q " \*qfrequency\*q
+.BI "Option \*qMinClock\*q \*q" frequency \*q
This optional entry specifies the minimum dot clock, in kHz, that is supported
by the monitor.
.TP 7
-.BI "Option " "\*qMaxClock\*q " \*qfrequency\*q
+.BI "Option \*qMaxClock\*q \*q" frequency \*q
This optional entry specifies the maximum dot clock, in kHz, that is supported
by the monitor.
.TP 7
-.BI "Option " "\*qIgnore\*q " \*qbool\*q
+.BI "Option \*qIgnore\*q \*q" bool \*q
This optional entry specifies that the monitor should be ignored entirely,
and not reported through RandR. This is useful if the hardware reports the
presence of outputs that don't exist.
(RandR 1.2-supporting drivers only)
.TP 7
-.BI "Option " "\*qRotate\*q " \*qrotation\*q
+.BI "Option \*qRotate\*q \*q" rotation \*q
This optional entry specifies the initial rotation of the given monitor.
Valid values for rotation are \*qnormal\*q, \*qleft\*q, \*qright\*q, and
\*qinverted\*q.
More information about the xorg-devel
mailing list