[Nouveau] [RFC v3 10/10] drm/dp: Extract i915's eDP backlight code into DRM helpers
Lyude Paul
lyude at redhat.com
Mon Feb 15 20:26:01 UTC 2021
On Mon, 2021-02-15 at 19:34 +0100, Thomas Zimmermann wrote:
> Hi
>
> Am 09.02.21 um 00:03 schrieb Lyude Paul:
> > >
> > > > + } else {
> > > > + buf[0] = level;
> > > > + }
> > > > +
> > > > + ret = drm_dp_dpcd_write(aux, DP_EDP_BACKLIGHT_BRIGHTNESS_MSB,
> > > > buf,
> > > > sizeof(buf));
> > > > + if (ret != sizeof(buf)) {
> > > > + DRM_ERROR("%s: Failed to write aux backlight level:
> > > > %d\n",
> > > > aux->name, ret);
> > >
> > > Since you're adding this code, you should probably convert to drm_err()
> > > helpers as well. Here and elsewhere.
> >
> > this is next up on my todo list JFYI-I don't do it right now because there
> > isn't
> > actually any backpointer to the drm driver (and you can't just use the
> > parent of
> > the aux device, since that technically doesn't need to be the drm driver).
> >
> > I'd add it in this series, but that's going to involve updating functions
> > across
> > the tree like drm_dp_aux_init() so I'd like to do it in a different patch
> > series
>
> Ok, sure. Makes sense.
I'm actually probably just going to do it anyway, since it seems like a want of
folks really want to keep the drm_dbg_*() prints around
>
> Best regards
> Thomas
>
> >
> > >
> > > > + return ret < 0 ? ret : -EIO;
> > > > + }
> > > > +
> > > > + return 0;
> > > > +}
> > > > +EXPORT_SYMBOL(drm_edp_backlight_set_level);
> > > > +
> > > > +static int
> > > > +drm_edp_backlight_set_enable(struct drm_dp_aux *aux, const struct
> > > > drm_edp_backlight_info *bl,
> > > > + bool enable)
> > > > +{
> > > > + int ret;
> > > > + u8 buf;
> > > > +
> > > > + /* The panel uses something other then DPCD for enabling it's
> > > > backlight */
> > >
> > > 'its'
> > >
> > > Best regards
> > > Thomas
> > >
> > > > + if (!bl->aux_enable)
> > > > + return 0;
> > > > +
> > > > + ret = drm_dp_dpcd_readb(aux, DP_EDP_DISPLAY_CONTROL_REGISTER,
> > > > &buf);
> > > > + if (ret != 1) {
> > > > + DRM_ERROR("%s: Failed to read eDP display control
> > > > register:
> > > > %d\n", aux->name, ret);
> > > > + return ret < 0 ? ret : -EIO;
> > > > + }
> > > > + if (enable)
> > > > + buf |= DP_EDP_BACKLIGHT_ENABLE;
> > > > + else
> > > > + buf &= ~DP_EDP_BACKLIGHT_ENABLE;
> > > > +
> > > > + ret = drm_dp_dpcd_writeb(aux, DP_EDP_DISPLAY_CONTROL_REGISTER,
> > > > buf);
> > > > + if (ret != 1) {
> > > > + DRM_ERROR("%s: Failed to write eDP display control
> > > > register:
> > > > %d\n", aux->name, ret);
> > > > + return ret < 0 ? ret : -EIO;
> > > > + }
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +/**
> > > > + * drm_edp_backlight_enable() - Enable an eDP panel's backlight using
> > > > DPCD
> > > > + * @aux: The DP AUX channel to use
> > > > + * @bl: Backlight capability info from drm_edp_backlight_init()
> > > > + * @level: The initial backlight level to set via AUX, if there is one
> > > > + *
> > > > + * This function handles enabling DPCD backlight controls on a panel
> > > > over
> > > > DPCD, while additionally
> > > > + * restoring any important backlight state such as the given backlight
> > > > level, the brightness byte
> > > > + * count, backlight frequency, etc.
> > > > + *
> > > > + * Note that certain panels, while supporting brightness level controls
> > > > over DPCD, may not support
> > > > + * having their backlights enabled via the standard
> > > > %DP_EDP_DISPLAY_CONTROL_REGISTER. On such panels
> > > > + * &drm_edp_backlight_info.aux_enable will be set to %false, this
> > > > function
> > > > will skip the step of
> > > > + * programming the %DP_EDP_DISPLAY_CONTROL_REGISTER, and the driver
> > > > must
> > > > perform the required
> > > > + * implementation specific step for enabling the backlight after
> > > > calling
> > > > this function.
> > > > + *
> > > > + * Returns: %0 on success, negative error code on failure.
> > > > + */
> > > > +int drm_edp_backlight_enable(struct drm_dp_aux *aux, const struct
> > > > drm_edp_backlight_info *bl,
> > > > + const u16 level)
> > > > +{
> > > > + int ret;
> > > > + u8 dpcd_buf, new_dpcd_buf;
> > > > +
> > > > + ret = drm_dp_dpcd_readb(aux, DP_EDP_BACKLIGHT_MODE_SET_REGISTER,
> > > > &dpcd_buf);
> > > > + if (ret != 1) {
> > > > + DRM_DEBUG_KMS("%s: Failed to read backlight mode: %d\n",
> > > > aux->name, ret);
> > > > + return ret < 0 ? ret : -EIO;
> > > > + }
> > > > +
> > > > + new_dpcd_buf = dpcd_buf;
> > > > +
> > > > + if ((dpcd_buf & DP_EDP_BACKLIGHT_CONTROL_MODE_MASK) !=
> > > > DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD) {
> > > > + new_dpcd_buf &= ~DP_EDP_BACKLIGHT_CONTROL_MODE_MASK;
> > > > + new_dpcd_buf |= DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD;
> > > > +
> > > > + ret = drm_dp_dpcd_writeb(aux, DP_EDP_PWMGEN_BIT_COUNT,
> > > > bl-
> > > > > pwmgen_bit_count);
> > > > + if (ret != 1)
> > > > + DRM_DEBUG_KMS("%s: Failed to write aux pwmgen
> > > > bit
> > > > count: %d\n",
> > > > + aux->name, ret);
> > > > + }
> > > > +
> > > > + if (bl->pwm_freq_pre_divider) {
> > > > + ret = drm_dp_dpcd_writeb(aux, DP_EDP_BACKLIGHT_FREQ_SET,
> > > > bl-
> > > > > pwm_freq_pre_divider);
> > > > + if (ret != 1)
> > > > + DRM_DEBUG_KMS("%s: Failed to write aux backlight
> > > > frequency: %d\n",
> > > > + aux->name, ret);
> > > > + else
> > > > + new_dpcd_buf |=
> > > > DP_EDP_BACKLIGHT_FREQ_AUX_SET_ENABLE;
> > > > + }
> > > > +
> > > > + if (new_dpcd_buf != dpcd_buf) {
> > > > + ret = drm_dp_dpcd_writeb(aux,
> > > > DP_EDP_BACKLIGHT_MODE_SET_REGISTER, new_dpcd_buf);
> > > > + if (ret != 1) {
> > > > + DRM_DEBUG_KMS("%s: Failed to write aux backlight
> > > > mode: %d\n",
> > > > + aux->name, ret);
> > > > + return ret < 0 ? ret : -EIO;
> > > > + }
> > > > + }
> > > > +
> > > > + ret = drm_edp_backlight_set_level(aux, bl, level);
> > > > + if (ret < 0)
> > > > + return ret;
> > > > + ret = drm_edp_backlight_set_enable(aux, bl, true);
> > > > + if (ret < 0)
> > > > + return ret;
> > > > +
> > > > + return 0;
> > > > +}
> > > > +EXPORT_SYMBOL(drm_edp_backlight_enable);
> > > > +
> > > > +/**
> > > > + * drm_edp_backlight_disable() - Disable an eDP backlight using DPCD,
> > > > if
> > > > supported
> > > > + * @aux: The DP AUX channel to use
> > > > + * @bl: Backlight capability info from drm_edp_backlight_init()
> > > > + *
> > > > + * This function handles disabling DPCD backlight controls on a panel
> > > > over
> > > > AUX. Note that some
> > > > + * panels have backlights that are enabled/disabled by other means,
> > > > despite
> > > > having their brightness
> > > > + * values controlled through DPCD. On such panels
> > > > &drm_edp_backlight_info.aux_enable will be set to
> > > > + * %false, this function will become a no-op (and we will skip updating
> > > > + * %DP_EDP_DISPLAY_CONTROL_REGISTER), and the driver must take care to
> > > > perform it's own
> > > > + * implementation specific step for disabling the backlight.
> > > > + *
> > > > + * Returns: %0 on success or no-op, negative error code on failure.
> > > > + */
> > > > +int drm_edp_backlight_disable(struct drm_dp_aux *aux, const struct
> > > > drm_edp_backlight_info *bl)
> > > > +{
> > > > + int ret;
> > > > +
> > > > + ret = drm_edp_backlight_set_enable(aux, bl, false);
> > > > + if (ret < 0)
> > > > + return ret;
> > > > +
> > > > + return 0;
> > > > +}
> > > > +EXPORT_SYMBOL(drm_edp_backlight_disable);
> > > > +
> > > > +static inline int
> > > > +drm_edp_backlight_probe_max(struct drm_dp_aux *aux, struct
> > > > drm_edp_backlight_info *bl,
> > > > + u16 driver_pwm_freq_hz, const u8
> > > > edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE])
> > > > +{
> > > > + int fxp, fxp_min, fxp_max, fxp_actual, f = 1;
> > > > + int ret;
> > > > + u8 pn, pn_min, pn_max;
> > > > +
> > > > + ret = drm_dp_dpcd_readb(aux, DP_EDP_PWMGEN_BIT_COUNT, &pn);
> > > > + if (ret != 1) {
> > > > + DRM_DEBUG_KMS("%s: Failed to read pwmgen bit count cap:
> > > > %d\n", aux->name, ret);
> > > > + return -ENODEV;
> > > > + }
> > > > +
> > > > + pn &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
> > > > + bl->max = (1 << pn) - 1;
> > > > + if (!driver_pwm_freq_hz)
> > > > + return 0;
> > > > +
> > > > + /*
> > > > + * Set PWM Frequency divider to match desired frequency provided
> > > > by
> > > > the driver.
> > > > + * The PWM Frequency is calculated as 27Mhz / (F x P).
> > > > + * - Where F = PWM Frequency Pre-Divider value programmed by
> > > > field
> > > > 7:0 of the
> > > > + * EDP_BACKLIGHT_FREQ_SET register (DPCD Address
> > > > 00728h)
> > > > + * - Where P = 2^Pn, where Pn is the value programmed by field
> > > > 4:0
> > > > of the
> > > > + * EDP_PWMGEN_BIT_COUNT register (DPCD Address
> > > > 00724h)
> > > > + */
> > > > +
> > > > + /* Find desired value of (F x P)
> > > > + * Note that, if F x P is out of supported range, the maximum
> > > > value
> > > > or minimum value will
> > > > + * applied automatically. So no need to check that.
> > > > + */
> > > > + fxp = DIV_ROUND_CLOSEST(1000 * DP_EDP_BACKLIGHT_FREQ_BASE_KHZ,
> > > > driver_pwm_freq_hz);
> > > > +
> > > > + /* Use highest possible value of Pn for more granularity of
> > > > brightness adjustment while
> > > > + * satifying the conditions below.
> > > > + * - Pn is in the range of Pn_min and Pn_max
> > > > + * - F is in the range of 1 and 255
> > > > + * - FxP is within 25% of desired value.
> > > > + * Note: 25% is arbitrary value and may need some tweak.
> > > > + */
> > > > + ret = drm_dp_dpcd_readb(aux, DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN,
> > > > &pn_min);
> > > > + if (ret != 1) {
> > > > + DRM_DEBUG_KMS("%s: Failed to read pwmgen bit count cap
> > > > min:
> > > > %d\n", aux->name, ret);
> > > > + return 0;
> > > > + }
> > > > + ret = drm_dp_dpcd_readb(aux, DP_EDP_PWMGEN_BIT_COUNT_CAP_MAX,
> > > > &pn_max);
> > > > + if (ret != 1) {
> > > > + DRM_DEBUG_KMS("%s: Failed to read pwmgen bit count cap
> > > > max:
> > > > %d\n", aux->name, ret);
> > > > + return 0;
> > > > + }
> > > > + pn_min &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
> > > > + pn_max &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
> > > > +
> > > > + /* Ensure frequency is within 25% of desired value */
> > > > + fxp_min = DIV_ROUND_CLOSEST(fxp * 3, 4);
> > > > + fxp_max = DIV_ROUND_CLOSEST(fxp * 5, 4);
> > > > + if (fxp_min < (1 << pn_min) || (255 << pn_max) < fxp_max) {
> > > > + DRM_DEBUG_KMS("%s: Driver defined backlight frequency
> > > > (%d)
> > > > out of range\n",
> > > > + aux->name, driver_pwm_freq_hz);
> > > > + return 0;
> > > > + }
> > > > +
> > > > + for (pn = pn_max; pn >= pn_min; pn--) {
> > > > + f = clamp(DIV_ROUND_CLOSEST(fxp, 1 << pn), 1, 255);
> > > > + fxp_actual = f << pn;
> > > > + if (fxp_min <= fxp_actual && fxp_actual <= fxp_max)
> > > > + break;
> > > > + }
> > > > +
> > > > + ret = drm_dp_dpcd_writeb(aux, DP_EDP_PWMGEN_BIT_COUNT, pn);
> > > > + if (ret != 1) {
> > > > + DRM_DEBUG_KMS("%s: Failed to write aux pwmgen bit count:
> > > > %d\n", aux->name, ret);
> > > > + return 0;
> > > > + }
> > > > + bl->pwmgen_bit_count = pn;
> > > > + bl->max = (1 << pn) - 1;
> > > > +
> > > > + if (edp_dpcd[2] & DP_EDP_BACKLIGHT_FREQ_AUX_SET_CAP) {
> > > > + bl->pwm_freq_pre_divider = f;
> > > > + DRM_DEBUG_KMS("%s: Using backlight frequency from driver
> > > > (%dHz)\n",
> > > > + aux->name, driver_pwm_freq_hz);
> > > > + }
> > > > +
> > > > + return 0;
> > > > +}
> > > > +
> > > > +static inline int
> > > > +drm_edp_backlight_probe_level(struct drm_dp_aux *aux, struct
> > > > drm_edp_backlight_info *bl,
> > > > + u8 *current_mode)
> > > > +{
> > > > + int ret;
> > > > + u8 buf[2];
> > > > + u8 mode_reg;
> > > > +
> > > > + ret = drm_dp_dpcd_readb(aux, DP_EDP_BACKLIGHT_MODE_SET_REGISTER,
> > > > &mode_reg);
> > > > + if (ret != 1) {
> > > > + DRM_DEBUG_KMS("%s: Failed to read backlight mode: %d\n",
> > > > aux->name, ret);
> > > > + return ret < 0 ? ret : -EIO;
> > > > + }
> > > > +
> > > > + *current_mode = (mode_reg & DP_EDP_BACKLIGHT_CONTROL_MODE_MASK);
> > > > + if (*current_mode == DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD) {
> > > > + int size = 1 + bl->lsb_reg_used;
> > > > +
> > > > + ret = drm_dp_dpcd_read(aux,
> > > > DP_EDP_BACKLIGHT_BRIGHTNESS_MSB,
> > > > buf, size);
> > > > + if (ret != size) {
> > > > + DRM_DEBUG_KMS("%s: Failed to read backlight
> > > > level:
> > > > %d\n", aux->name, ret);
> > > > + return ret < 0 ? ret : -EIO;
> > > > + }
> > > > +
> > > > + if (bl->lsb_reg_used)
> > > > + return (buf[0] << 8) | buf[1];
> > > > + else
> > > > + return buf[0];
> > > > + }
> > > > +
> > > > + /*
> > > > + * If we're not in DPCD control mode yet, the programmed
> > > > brightness
> > > > value is meaningless and
> > > > + * the driver should assume max brightness
> > > > + */
> > > > + return bl->max;
> > > > +}
> > > > +
> > > > +/**
> > > > + * drm_edp_backlight_init() - Probe a display panel's TCON using the
> > > > standard VESA eDP backlight
> > > > + * interface.
> > > > + * @aux: The DP aux device to use for probing
> > > > + * @bl: The &drm_edp_backlight_info struct to fill out with information
> > > > on
> > > > the backlight
> > > > + * @driver_pwm_freq_hz: Optional PWM frequency from the driver in hz
> > > > + * @edp_dpcd: A cached copy of the eDP DPCD
> > > > + * @current_level: Where to store the probed brightness level
> > > > + * @current_mode: Where to store the currently set backlight control
> > > > mode
> > > > + *
> > > > + * Initializes a &drm_edp_backlight_info struct by probing @aux for
> > > > it's
> > > > backlight capabilities,
> > > > + * along with also probing the current and maximum supported brightness
> > > > levels.
> > > > + *
> > > > + * If @driver_pwm_freq_hz is non-zero, this will be used as the
> > > > backlight
> > > > frequency. Otherwise, the
> > > > + * default frequency from the panel is used.
> > > > + *
> > > > + * Returns: %0 on success, negative error code on failure.
> > > > + */
> > > > +int
> > > > +drm_edp_backlight_init(struct drm_dp_aux *aux, struct
> > > > drm_edp_backlight_info *bl,
> > > > + u16 driver_pwm_freq_hz, const u8
> > > > edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE],
> > > > + u16 *current_level, u8 *current_mode)
> > > > +{
> > > > + int ret;
> > > > +
> > > > + if (edp_dpcd[1] & DP_EDP_BACKLIGHT_AUX_ENABLE_CAP)
> > > > + bl->aux_enable = true;
> > > > + if (edp_dpcd[2] & DP_EDP_BACKLIGHT_BRIGHTNESS_BYTE_COUNT)
> > > > + bl->lsb_reg_used = true;
> > > > +
> > > > + ret = drm_edp_backlight_probe_max(aux, bl, driver_pwm_freq_hz,
> > > > edp_dpcd);
> > > > + if (ret < 0)
> > > > + return ret;
> > > > +
> > > > + ret = drm_edp_backlight_probe_level(aux, bl, current_mode);
> > > > + if (ret < 0)
> > > > + return ret;
> > > > + *current_level = ret;
> > > > +
> > > > + DRM_DEBUG_KMS("%s: Found backlight level=%d/%d
> > > > pwm_freq_pre_divider=%d mode=%x\n",
> > > > + aux->name, *current_level, bl->max, bl-
> > > > > pwm_freq_pre_divider, *current_mode);
> > > > + DRM_DEBUG_KMS("%s: Backlight caps: pwmgen_bit_count=%d
> > > > lsb_reg_used=%d aux_enable=%d\n",
> > > > + aux->name, bl->pwmgen_bit_count, bl->lsb_reg_used,
> > > > bl-
> > > > > aux_enable);
> > > > + return 0;
> > > > +}
> > > > +EXPORT_SYMBOL(drm_edp_backlight_init);
> > > > diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h
> > > > b/drivers/gpu/drm/i915/display/intel_display_types.h
> > > > index 16824eb3ef93..03051ab75d30 100644
> > > > --- a/drivers/gpu/drm/i915/display/intel_display_types.h
> > > > +++ b/drivers/gpu/drm/i915/display/intel_display_types.h
> > > > @@ -263,10 +263,7 @@ struct intel_panel {
> > > > /* DPCD backlight */
> > > > union {
> > > > struct {
> > > > - u8 pwmgen_bit_count;
> > > > - u8 pwm_freq_pre_divider;
> > > > - bool lsb_reg_used;
> > > > - bool aux_enable;
> > > > + struct drm_edp_backlight_info info;
> > > > } vesa;
> > > > struct {
> > > > bool sdr_uses_aux;
> > > > diff --git a/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c
> > > > b/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c
> > > > index 813f6c553156..286eb337448e 100644
> > > > --- a/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c
> > > > +++ b/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c
> > > > @@ -270,114 +270,19 @@ intel_dp_aux_hdr_setup_backlight(struct
> > > > intel_connector *connector, enum pipe pi
> > > > }
> > > >
> > > > /* VESA backlight callbacks */
> > > > -static bool intel_dp_aux_vesa_backlight_dpcd_mode(struct
> > > > intel_connector
> > > > *connector)
> > > > -{
> > > > - struct intel_dp *intel_dp = intel_attached_dp(connector);
> > > > - struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> > > > - int ret;
> > > > - u8 mode_reg;
> > > > -
> > > > - ret = drm_dp_dpcd_readb(&intel_dp->aux,
> > > > DP_EDP_BACKLIGHT_MODE_SET_REGISTER, &mode_reg);
> > > > - if (ret != 1) {
> > > > - drm_dbg_kms(&i915->drm, "Failed to read backlight mode:
> > > > %d\n", ret);
> > > > - return false;
> > > > - }
> > > > -
> > > > - return (mode_reg & DP_EDP_BACKLIGHT_CONTROL_MODE_MASK) ==
> > > > - DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD;
> > > > -}
> > > > -
> > > > -/*
> > > > - * Read the current backlight value from DPCD register(s) based
> > > > - * on if 8-bit(MSB) or 16-bit(MSB and LSB) values are supported
> > > > - */
> > > > static u32 intel_dp_aux_vesa_get_backlight(struct intel_connector
> > > > *connector, enum pipe unused)
> > > > {
> > > > - struct intel_dp *intel_dp = intel_attached_dp(connector);
> > > > - struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> > > > - int ret;
> > > > - u8 read_val[2] = { 0x0 };
> > > > - u16 level = 0;
> > > > -
> > > > - /*
> > > > - * If we're not in DPCD control mode yet, the programmed
> > > > brightness
> > > > - * value is meaningless and we should assume max brightness
> > > > - */
> > > > - if (!intel_dp_aux_vesa_backlight_dpcd_mode(connector))
> > > > - return connector->panel.backlight.max;
> > > > -
> > > > - ret = drm_dp_dpcd_read(&intel_dp->aux,
> > > > DP_EDP_BACKLIGHT_BRIGHTNESS_MSB, &read_val,
> > > > - sizeof(read_val));
> > > > - if (ret != sizeof(read_val)) {
> > > > - drm_dbg_kms(&i915->drm, "Failed to read brightness
> > > > level:
> > > > %d\n", ret);
> > > > - return 0;
> > > > - }
> > > > -
> > > > - if (connector->panel.backlight.edp.vesa.lsb_reg_used)
> > > > - level = (read_val[0] << 8 | read_val[1]);
> > > > - else
> > > > - level = read_val[0];
> > > > -
> > > > - return level;
> > > > + return connector->panel.backlight.level;
> > > > }
> > > >
> > > > -/*
> > > > - * Sends the current backlight level over the aux channel, checking if
> > > > its
> > > > using
> > > > - * 8-bit or 16 bit value (MSB and LSB)
> > > > - */
> > > > static void
> > > > -intel_dp_aux_vesa_set_backlight(const struct drm_connector_state
> > > > *conn_state,
> > > > - u32 level)
> > > > +intel_dp_aux_vesa_set_backlight(const struct drm_connector_state
> > > > *conn_state, u32 level)
> > > > {
> > > > struct intel_connector *connector =
> > > > to_intel_connector(conn_state-
> > > > > connector);
> > > > - struct intel_dp *intel_dp = intel_attached_dp(connector);
> > > > - struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> > > > - int ret;
> > > > - u8 vals[2] = { 0x0 };
> > > > -
> > > > - /* Write the MSB and/or LSB */
> > > > - if (connector->panel.backlight.edp.vesa.lsb_reg_used) {
> > > > - vals[0] = (level & 0xFF00) >> 8;
> > > > - vals[1] = (level & 0xFF);
> > > > - } else {
> > > > - vals[0] = level;
> > > > - }
> > > > -
> > > > - ret = drm_dp_dpcd_write(&intel_dp->aux,
> > > > DP_EDP_BACKLIGHT_BRIGHTNESS_MSB, vals,
> > > > - sizeof(vals));
> > > > - if (ret != sizeof(vals)) {
> > > > - drm_dbg_kms(&i915->drm, "Failed to write aux backlight
> > > > level: %d\n", ret);
> > > > - return;
> > > > - }
> > > > -}
> > > > -
> > > > -static void set_vesa_backlight_enable(struct intel_connector
> > > > *connector,
> > > > bool enable)
> > > > -{
> > > > - struct intel_dp *intel_dp = intel_attached_dp(connector);
> > > > - struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> > > > - int ret;
> > > > - u8 reg_val = 0;
> > > > -
> > > > - /* Early return when display use other mechanism to enable
> > > > backlight. */
> > > > - if (!connector->panel.backlight.edp.vesa.aux_enable)
> > > > - return;
> > > > -
> > > > - ret = drm_dp_dpcd_readb(&intel_dp->aux,
> > > > DP_EDP_DISPLAY_CONTROL_REGISTER, ®_val);
> > > > - if (ret != 1) {
> > > > - drm_dbg_kms(&i915->drm, "Failed to read eDP display
> > > > control
> > > > register: %d\n", ret);
> > > > - return;
> > > > - }
> > > > -
> > > > - if (enable)
> > > > - reg_val |= DP_EDP_BACKLIGHT_ENABLE;
> > > > - else
> > > > - reg_val &= ~(DP_EDP_BACKLIGHT_ENABLE);
> > > > + struct intel_panel *panel = &connector->panel;
> > > > + struct intel_dp *intel_dp = enc_to_intel_dp(connector->encoder);
> > > >
> > > > - ret = drm_dp_dpcd_writeb(&intel_dp->aux,
> > > > DP_EDP_DISPLAY_CONTROL_REGISTER, reg_val);
> > > > - if (ret != 1) {
> > > > - drm_dbg_kms(&i915->drm, "Failed to %s aux backlight:
> > > > %d\n",
> > > > - enable ? "enable" : "disable", ret);
> > > > - }
> > > > + drm_edp_backlight_set_level(&intel_dp->aux, &panel-
> > > > > backlight.edp.vesa.info, level);
> > > > }
> > > >
> > > > static void
> > > > @@ -385,170 +290,46 @@ intel_dp_aux_vesa_enable_backlight(const struct
> > > > intel_crtc_state *crtc_state,
> > > > const struct drm_connector_state
> > > > *conn_state, u32 level)
> > > > {
> > > > struct intel_connector *connector =
> > > > to_intel_connector(conn_state-
> > > > > connector);
> > > > - struct intel_dp *intel_dp = intel_attached_dp(connector);
> > > > - struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> > > > struct intel_panel *panel = &connector->panel;
> > > > - int ret;
> > > > - u8 dpcd_buf, new_dpcd_buf;
> > > > - u8 pwmgen_bit_count = panel-
> > > > >backlight.edp.vesa.pwmgen_bit_count;
> > > > -
> > > > - ret = drm_dp_dpcd_readb(&intel_dp->aux,
> > > > DP_EDP_BACKLIGHT_MODE_SET_REGISTER, &dpcd_buf);
> > > > - if (ret != 1) {
> > > > - drm_dbg_kms(&i915->drm, "Failed to read backlight mode:
> > > > %d\n", ret);
> > > > - return;
> > > > - }
> > > > -
> > > > - new_dpcd_buf = dpcd_buf;
> > > > -
> > > > - if ((dpcd_buf & DP_EDP_BACKLIGHT_CONTROL_MODE_MASK) !=
> > > > DP_EDP_BACKLIGHT_CONTROL_MODE_MASK) {
> > > > - new_dpcd_buf &= ~DP_EDP_BACKLIGHT_CONTROL_MODE_MASK;
> > > > - new_dpcd_buf |= DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD;
> > > > -
> > > > - ret = drm_dp_dpcd_writeb(&intel_dp->aux,
> > > > DP_EDP_PWMGEN_BIT_COUNT, pwmgen_bit_count);
> > > > - if (ret != 1)
> > > > - drm_dbg_kms(&i915->drm, "Failed to write aux
> > > > pwmgen
> > > > bit count: %d\n", ret);
> > > > - }
> > > > -
> > > > - if (panel->backlight.edp.vesa.pwm_freq_pre_divider) {
> > > > - ret = drm_dp_dpcd_writeb(&intel_dp->aux,
> > > > DP_EDP_BACKLIGHT_FREQ_SET,
> > > > - panel-
> > > > > backlight.edp.vesa.pwm_freq_pre_divider);
> > > > - if (ret == 1)
> > > > - new_dpcd_buf |=
> > > > DP_EDP_BACKLIGHT_FREQ_AUX_SET_ENABLE;
> > > > - else
> > > > - drm_dbg_kms(&i915->drm, "Failed to write aux
> > > > backlight frequency: %d\n",
> > > > - ret);
> > > > - }
> > > > -
> > > > - if (new_dpcd_buf != dpcd_buf) {
> > > > - ret = drm_dp_dpcd_writeb(&intel_dp->aux,
> > > > DP_EDP_BACKLIGHT_MODE_SET_REGISTER,
> > > > - new_dpcd_buf);
> > > > - if (ret != 1)
> > > > - drm_dbg_kms(&i915->drm, "Failed to write aux
> > > > backlight mode: %d\n", ret);
> > > > - }
> > > > + struct intel_dp *intel_dp = enc_to_intel_dp(connector->encoder);
> > > >
> > > > - intel_dp_aux_vesa_set_backlight(conn_state, level);
> > > > - set_vesa_backlight_enable(connector, true);
> > > > + drm_edp_backlight_enable(&intel_dp->aux, &panel-
> > > > > backlight.edp.vesa.info, level);
> > > > }
> > > >
> > > > static void intel_dp_aux_vesa_disable_backlight(const struct
> > > > drm_connector_state *old_conn_state,
> > > > u32 level)
> > > > {
> > > > - set_vesa_backlight_enable(to_intel_connector(old_conn_state-
> > > > > connector), false);
> > > > -}
> > > > -
> > > > -/*
> > > > - * Compute PWM frequency divider value based off the frequency provided
> > > > to
> > > > us by the vbt.
> > > > - * The PWM Frequency is calculated as 27Mhz / (F x P).
> > > > - * - Where F = PWM Frequency Pre-Divider value programmed by field 7:0
> > > > of
> > > > the
> > > > - * EDP_BACKLIGHT_FREQ_SET register (DPCD Address 00728h)
> > > > - * - Where P = 2^Pn, where Pn is the value programmed by field 4:0 of
> > > > the
> > > > - * EDP_PWMGEN_BIT_COUNT register (DPCD Address 00724h)
> > > > - */
> > > > -static u32 intel_dp_aux_vesa_calc_max_backlight(struct intel_connector
> > > > *connector)
> > > > -{
> > > > - struct drm_i915_private *i915 = to_i915(connector->base.dev);
> > > > - struct intel_dp *intel_dp = intel_attached_dp(connector);
> > > > + struct intel_connector *connector =
> > > > to_intel_connector(old_conn_state->connector);
> > > > struct intel_panel *panel = &connector->panel;
> > > > - u32 max_backlight = 0;
> > > > - int ret, freq, fxp, fxp_min, fxp_max, fxp_actual, f = 1;
> > > > - u8 pn, pn_min, pn_max;
> > > > -
> > > > - ret = drm_dp_dpcd_readb(&intel_dp->aux, DP_EDP_PWMGEN_BIT_COUNT,
> > > > &pn);
> > > > - if (ret != 1) {
> > > > - drm_dbg_kms(&i915->drm, "Failed to read pwmgen bit count
> > > > cap: %d\n", ret);
> > > > - return 0;
> > > > - }
> > > > -
> > > > - pn &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
> > > > - max_backlight = (1 << pn) - 1;
> > > > -
> > > > - /* Find desired value of (F x P)
> > > > - * Note that, if F x P is out of supported range, the maximum
> > > > value
> > > > or
> > > > - * minimum value will applied automatically. So no need to check
> > > > that.
> > > > - */
> > > > - freq = i915->vbt.backlight.pwm_freq_hz;
> > > > - drm_dbg_kms(&i915->drm, "VBT defined backlight frequency %u
> > > > Hz\n",
> > > > - freq);
> > > > - if (!freq) {
> > > > - drm_dbg_kms(&i915->drm,
> > > > - "Use panel default backlight frequency\n");
> > > > - return max_backlight;
> > > > - }
> > > > -
> > > > - fxp = DIV_ROUND_CLOSEST(KHz(DP_EDP_BACKLIGHT_FREQ_BASE_KHZ),
> > > > freq);
> > > > -
> > > > - /* Use highest possible value of Pn for more granularity of
> > > > brightness
> > > > - * adjustment while satifying the conditions below.
> > > > - * - Pn is in the range of Pn_min and Pn_max
> > > > - * - F is in the range of 1 and 255
> > > > - * - FxP is within 25% of desired value.
> > > > - * Note: 25% is arbitrary value and may need some tweak.
> > > > - */
> > > > - ret = drm_dp_dpcd_readb(&intel_dp->aux,
> > > > DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN, &pn_min);
> > > > - if (ret != 1) {
> > > > - drm_dbg_kms(&i915->drm, "Failed to read pwmgen bit count
> > > > cap
> > > > min: %d\n", ret);
> > > > - return max_backlight;
> > > > - }
> > > > - ret = drm_dp_dpcd_readb(&intel_dp->aux,
> > > > DP_EDP_PWMGEN_BIT_COUNT_CAP_MAX, &pn_max);
> > > > - if (ret != 1) {
> > > > - drm_dbg_kms(&i915->drm, "Failed to read pwmgen bit count
> > > > cap
> > > > max: %d\n", ret);
> > > > - return max_backlight;
> > > > - }
> > > > - pn_min &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
> > > > - pn_max &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
> > > > -
> > > > - /* Ensure frequency is within 25% of desired value */
> > > > - fxp_min = DIV_ROUND_CLOSEST(fxp * 3, 4);
> > > > - fxp_max = DIV_ROUND_CLOSEST(fxp * 5, 4);
> > > > -
> > > > - if (fxp_min < (1 << pn_min) || (255 << pn_max) < fxp_max) {
> > > > - drm_dbg_kms(&i915->drm,
> > > > - "VBT defined backlight frequency out of
> > > > range\n");
> > > > - return max_backlight;
> > > > - }
> > > > -
> > > > - for (pn = pn_max; pn >= pn_min; pn--) {
> > > > - f = clamp(DIV_ROUND_CLOSEST(fxp, 1 << pn), 1, 255);
> > > > - fxp_actual = f << pn;
> > > > - if (fxp_min <= fxp_actual && fxp_actual <= fxp_max)
> > > > - break;
> > > > - }
> > > > -
> > > > - drm_dbg_kms(&i915->drm, "Using eDP pwmgen bit count of %d\n",
> > > > pn);
> > > > - ret = drm_dp_dpcd_writeb(&intel_dp->aux,
> > > > DP_EDP_PWMGEN_BIT_COUNT,
> > > > pn);
> > > > - if (ret != 1) {
> > > > - drm_dbg_kms(&i915->drm, "Failed to write aux pwmgen bit
> > > > count: %d\n", ret);
> > > > - return max_backlight;
> > > > - }
> > > > -
> > > > - panel->backlight.edp.vesa.pwmgen_bit_count = pn;
> > > > - if (intel_dp->edp_dpcd[2] & DP_EDP_BACKLIGHT_FREQ_AUX_SET_CAP)
> > > > - panel->backlight.edp.vesa.pwm_freq_pre_divider = f;
> > > > -
> > > > - max_backlight = (1 << pn) - 1;
> > > > + struct intel_dp *intel_dp = enc_to_intel_dp(connector->encoder);
> > > >
> > > > - return max_backlight;
> > > > + drm_edp_backlight_disable(&intel_dp->aux, &panel-
> > > > > backlight.edp.vesa.info);
> > > > }
> > > >
> > > > -static int intel_dp_aux_vesa_setup_backlight(struct intel_connector
> > > > *connector,
> > > > - enum pipe pipe)
> > > > +static int intel_dp_aux_vesa_setup_backlight(struct intel_connector
> > > > *connector, enum pipe pipe)
> > > > {
> > > > struct intel_dp *intel_dp = intel_attached_dp(connector);
> > > > struct intel_panel *panel = &connector->panel;
> > > > + struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> > > > + u16 current_level;
> > > > + u8 current_mode;
> > > > + int ret;
> > > >
> > > > - if (intel_dp->edp_dpcd[1] & DP_EDP_BACKLIGHT_AUX_ENABLE_CAP)
> > > > - panel->backlight.edp.vesa.aux_enable = true;
> > > > - if (intel_dp->edp_dpcd[2] &
> > > > DP_EDP_BACKLIGHT_BRIGHTNESS_BYTE_COUNT)
> > > > - panel->backlight.edp.vesa.lsb_reg_used = true;
> > > > -
> > > > - panel->backlight.max =
> > > > intel_dp_aux_vesa_calc_max_backlight(connector);
> > > > - if (!panel->backlight.max)
> > > > - return -ENODEV;
> > > > + ret = drm_edp_backlight_init(&intel_dp->aux, &panel-
> > > > > backlight.edp.vesa.info,
> > > > + i915->vbt.backlight.pwm_freq_hz,
> > > > intel_dp->edp_dpcd,
> > > > + ¤t_level, ¤t_mode);
> > > > + if (ret < 0)
> > > > + return ret;
> > > >
> > > > + panel->backlight.max = panel->backlight.edp.vesa.info.max;
> > > > panel->backlight.min = 0;
> > > > - panel->backlight.level =
> > > > intel_dp_aux_vesa_get_backlight(connector,
> > > > pipe);
> > > > - panel->backlight.enabled =
> > > > intel_dp_aux_vesa_backlight_dpcd_mode(connector) &&
> > > > - panel->backlight.level != 0;
> > > > + if (current_mode == DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD) {
> > > > + panel->backlight.level = current_level;
> > > > + panel->backlight.enabled = panel->backlight.level != 0;
> > > > + } else {
> > > > + panel->backlight.level = panel->backlight.max;
> > > > + panel->backlight.enabled = false;
> > > > + }
> > > >
> > > > return 0;
> > > > }
> > > > @@ -559,16 +340,12 @@ intel_dp_aux_supports_vesa_backlight(struct
> > > > intel_connector *connector)
> > > > struct intel_dp *intel_dp = intel_attached_dp(connector);
> > > > struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> > > >
> > > > - /* Check the eDP Display control capabilities registers to
> > > > determine
> > > > if
> > > > - * the panel can support backlight control over the aux channel.
> > > > - *
> > > > - * TODO: We currently only support AUX only backlight
> > > > configurations, not backlights which
> > > > + /* TODO: We currently only support AUX only backlight
> > > > configurations, not backlights which
> > > > * require a mix of PWM and AUX controls to work. In the mean
> > > > time,
> > > > these machines typically
> > > > * work just fine using normal PWM controls anyway.
> > > > */
> > > > - if (intel_dp->edp_dpcd[1] & DP_EDP_TCON_BACKLIGHT_ADJUSTMENT_CAP
> > > > &&
> > > > - (intel_dp->edp_dpcd[1] & DP_EDP_BACKLIGHT_AUX_ENABLE_CAP) &&
> > > > - (intel_dp->edp_dpcd[2] &
> > > > DP_EDP_BACKLIGHT_BRIGHTNESS_AUX_SET_CAP)) {
> > > > + if ((intel_dp->edp_dpcd[1] & DP_EDP_BACKLIGHT_AUX_ENABLE_CAP) &&
> > > > + drm_edp_backlight_supported(intel_dp->edp_dpcd)) {
> > > > drm_dbg_kms(&i915->drm, "AUX Backlight Control
> > > > Supported!\n");
> > > > return true;
> > > > }
> > > > diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h
> > > > index edffd1dcca3e..1eca0b42fc45 100644
> > > > --- a/include/drm/drm_dp_helper.h
> > > > +++ b/include/drm/drm_dp_helper.h
> > > > @@ -1790,6 +1790,24 @@ drm_dp_sink_can_do_video_without_timing_msa(const
> > > > u8
> > > > dpcd[DP_RECEIVER_CAP_SIZE])
> > > > DP_MSA_TIMING_PAR_IGNORED;
> > > > }
> > > >
> > > > +/**
> > > > + * drm_edp_backlight_supported() - Check an eDP DPCD for VESA backlight
> > > > support
> > > > + * @edp_dpcd: The DPCD to check
> > > > + *
> > > > + * Note that currently this function will return %false for panels
> > > > which
> > > > support various DPCD
> > > > + * backlight features but which require the brightness be set through
> > > > PWM,
> > > > and don't support setting
> > > > + * the brightness level via the DPCD. This is a TODO.
> > > > + *
> > > > + * Returns: %True if @edp_dpcd indicates that VESA backlight controls
> > > > are
> > > > supported, %false
> > > > + * otherwise
> > > > + */
> > > > +static inline bool
> > > > +drm_edp_backlight_supported(const u8
> > > > edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE])
> > > > +{
> > > > + return (edp_dpcd[1] & DP_EDP_TCON_BACKLIGHT_ADJUSTMENT_CAP) &&
> > > > + (edp_dpcd[2] & DP_EDP_BACKLIGHT_BRIGHTNESS_AUX_SET_CAP);
> > > > +}
> > > > +
> > > > /*
> > > > * DisplayPort AUX channel
> > > > */
> > > > @@ -2089,6 +2107,36 @@ drm_dp_has_quirk(const struct drm_dp_desc *desc,
> > > > enum
> > > > drm_dp_quirk quirk)
> > > > return desc->quirks & BIT(quirk);
> > > > }
> > > >
> > > > +/**
> > > > + * struct drm_edp_backlight_info - Probed eDP backlight info struct
> > > > + * @pwmgen_bit_count: The pwmgen bit count
> > > > + * @pwm_freq_pre_divider: The PWM frequency pre-divider value being
> > > > used
> > > > for this backlight, if any
> > > > + * @max: The maximum backlight level that may be set
> > > > + * @lsb_reg_used: Do we also write values to the
> > > > DP_EDP_BACKLIGHT_BRIGHTNESS_LSB register?
> > > > + * @aux_enable: Does the panel support the AUX enable cap?
> > > > + *
> > > > + * This structure contains various data about an eDP backlight, which
> > > > can
> > > > be populated by using
> > > > + * drm_edp_backlight_init().
> > > > + */
> > > > +struct drm_edp_backlight_info {
> > > > + u8 pwmgen_bit_count;
> > > > + u8 pwm_freq_pre_divider;
> > > > + u16 max;
> > > > +
> > > > + bool lsb_reg_used : 1;
> > > > + bool aux_enable : 1;
> > > > +};
> > > > +
> > > > +int
> > > > +drm_edp_backlight_init(struct drm_dp_aux *aux, struct
> > > > drm_edp_backlight_info *bl,
> > > > + u16 driver_pwm_freq_hz, const u8
> > > > edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE],
> > > > + u16 *current_level, u8 *current_mode);
> > > > +int drm_edp_backlight_set_level(struct drm_dp_aux *aux, const struct
> > > > drm_edp_backlight_info *bl,
> > > > + u16 level);
> > > > +int drm_edp_backlight_enable(struct drm_dp_aux *aux, const struct
> > > > drm_edp_backlight_info *bl,
> > > > + u16 level);
> > > > +int drm_edp_backlight_disable(struct drm_dp_aux *aux, const struct
> > > > drm_edp_backlight_info *bl);
> > > > +
> > > > #ifdef CONFIG_DRM_DP_CEC
> > > > void drm_dp_cec_irq(struct drm_dp_aux *aux);
> > > > void drm_dp_cec_register_connector(struct drm_dp_aux *aux,
> > > >
> > >
> >
>
--
Sincerely,
Lyude Paul (she/her)
Software Engineer at Red Hat
Note: I deal with a lot of emails and have a lot of bugs on my plate. If you've
asked me a question, are waiting for a review/merge on a patch, etc. and I
haven't responded in a while, please feel free to send me another email to check
on my status. I don't bite!
More information about the Nouveau
mailing list