[PATCH v12 00/18] drm: Add Samsung MIPI DSIM bridge

Alexander Stein alexander.stein at ew.tq-group.com
Fri Feb 17 10:05:15 UTC 2023


Am Freitag, 17. Februar 2023, 09:55:22 CET schrieb Rasmus Villemoes:
> On 14/02/2023 12.09, Fabio Estevam wrote:
> > Hi Rasmus,
> > 
> > On Tue, Feb 14, 2023 at 7:55 AM Rasmus Villemoes
> > 
> > <rasmus.villemoes at prevas.dk> wrote:
> >> Well, the data sheet for the dsi86 says up to 750MHz DSI HS clock, and
> >> if the value specified in samsung,burst-clock-frequency is twice the DSI
> >> HS clk, I suppose I should be good up to 1.5GHz? I have tried many
> >> different values, but I never seem to get anything through; I think I'm
> >> missing some piece.
> >> 
> >> So now I've tried to use these patches on the imx8mp-evk with the
> >> mipi->hdmi accessory from NXP, just to see if I can ever get any
> >> graphics through the mipi interface. And there the story is the same:
> >> the adv7535 bridge gets probed, and can read out the edid from the
> >> monitor over hdmi. And while the mipi block and the bridge seem to
> >> attach to each other, I still don't get any output.
> >> 
> >> Do any of you happen to have this working on the imx8mp-evk, and if so,
> >> can you share the .dts updates you've done and how exactly you test the
> >> graphics?
> > 
> > I don't have access to an imx8mp-evk, but I tested the ADV7535 MIPI to
> > HDMI daughter card on an imx8mm-evk.
> > 
> > Some extra ADV7535 patches were needed. Please check patches 0020-0023
> > and see if they help.
> 
> Thanks, but they don't seem to make a difference.
> 
> I've started trying to simply compare registers between the NXP 5.15
> kernel and the imx8mm-dsi-v12 branch with Marek's patch on top. Already
> in MEDIA_BLK_CTRL, 0x32ec0000, there's something interesting:
> 
>  ## Media Mix Clock Enable Register
> -CLK_EN                 0004    0080e133
> +CLK_EN                 0004    00800133
>  ## MIPI PHY Control Register
> -MIPI_RESET_DIV         0008    40030000
> +MIPI_RESET_DIV         0008    00020000
> 
> So with the NXP kernel, there are three bits set in CLK_EN which are not
> set with the "mainline", but those bits are marked reserved in the RM,
> so I have no idea if they are just some RO bits that get set due to some
> other munging. Then there's the MIPI_RESET_DIV register where bits 16
> and 30 do not get set. Of course, there are lots of other differences,
> but perhaps this gives somebody an idea.

Looking at drivers/soc/imx/imx8m-blk-ctrl.c the bits for MIPI_RESET_DIV are
16: MIPI_CSI1
17: MIPI_DSI
30: MIPI_CSI2
So i think that's okay here.

Best regards,
Alexander
-- 
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
http://www.tq-group.com/




More information about the dri-devel mailing list